How to Make a Dorset Button

How to make a Crosswheel Dorset Button

Let’s get one thing straight from the start.   Dorset buttons are not hard.  A bit fiddly perhaps but not hard, so don’t you go giving up before you have even started.  Plus, I have written these instructions assuming that you know nothing, so each and every stage is covered. Those people who know a little bit more than nothing can ignore what is written in italics, these bits are for complete beginners.

NB I am left handed so if you are right you may find it easier to work in the opposite direction to me.

 

You will need

A curtain ring

Fine (2 ply or crewel) wool

crochet cotton or 2 ply wool (size 10 works for me)

Short large eyed blunt needle

Short large eyed sharp needle (this is for casting off if you need to)

 

Casting or covering the ring

1. Thread your needle with about 2.5 metres of your chosen wool or cotton.  You need it this long to cover the whole of the ring and create the spokes of the wheel without having to cast on again

2. Loop thread around ring a couple of times to hold it steady whilst you start off and then blanket stitch* all around the ring.

 

4.  Keep stitches fairly tight and evenly pushed together to cover the ring.  Use the loose end to help hold ring steady.

5.   When you have almost gone around the ring you need to tie in the loose end.  Lie it flat along the ring and blanket stitch over top of it.  Finish blanket stitching and slip needle through the first stitch to finish off.  Then pull the loose end tight and trim (Don’t cut main thread, you haven’t finished yet)

Slicking or pushing ridge of the stitch to the inside

Twist the stitches so the ridge is facing inwards.  You can do it gradually and a thumb nail is the perfect implement for this job.

Laying or making the spokes

1.    Have the thread to the front of the ring at 12.00, bring it down to the bottom and bring it back up the back in exactly the middle.  Try and make the blanket stitches part slightly so that your spokes lie flat next to them.

 

2.   Turn the ring ever so slightly and continue to wind over and over to create the spokes.  Aim for eight or twelve spokes for the first button and definitely only eight if you are using wool.  Don’t worry if the spokes look off centre at this stage.

See how the spokes of the wheel are not centred until you have secured them with holding stitch

3.   When you have got back to your first spoke end by taking needle through stitches in the centre from front to back.  Gently nudge the spokes with the needle, so they all cross over each other at the centre.

 

4.    Then bring the needle back up through the stitches and wiggle threads again to ensure the spokes are definitely centred and then do another stitch to secure spokes and to make sure they stay centred.  Make theses two stitches a neat cross as they will show.

Rounding or filling in the gaps

You should still have enough thread left to carry on without casting on or you may wish to change colour at this stage.

1.   Starting in the centre, use back stitch* to loop around each spoke in turn.  Use the needle to nudge each stitch towards the middle.

2.   When you have gone around the wheel once, take a good look at the spokes and make sure they are centred, if they are slightly off then push to the middle with your needle.  This is the last chance to wiggle them and its really easy to forget to do this bit.

2.   After a couple of circuits you will start to see the ridges forming around the spokes.  Fill in the whole wheel or stop whenever it tickles your fancy.

3.   If you need to change thread during this stage. Cast on or off by running thread up or down one of the spokes.

Top tip – there is no need to pull all the thread to the front of the button and then pull it all back to the back.  Bring the needle to the front pull a little thread through, take your stitch back down and then pull all the thread through at once.

4.  Keep pushing the stitches towards the centre of the button to keep everything tight and tidy.

 

And there you go!  Once you have made a basic button it is time to start experimenting.  See my next post for some buttons that I have been making.

 

*Blanket stitch

a. Start with your thread coming through ring from the back to the front at the top.

b.  Pass needle through centre of ring from behind.

c.  You will have created a loop.  Pass needle through this loop

d.  Pull all your thread through loop and pull stitch tight.

e. Repeat stages b-d over and over again!

 

 

 *Back Stitch Weave

a.  Bring needle up through the button on the left of top spoke.

b.  Go down through the button to the right of that spoke.

NB -the button is slightly wonky in this photo.  

c.  Pull tight.

d. Working anticlockwise, bring needle back up through to the left of the next spoke (i.e 11 o’clock)

e. Go down through the button to the right of that spoke.  You can hardly see the first few stitches but it becomes clearer as you go on.

f. Repeat over and over.  Remember; up on the left, down on the right. Working anticlockwise around the button.

 

Is this tutorial clear?  Is there a glaring error?  Please let me know and give me a pat on the back if it’s useful!!

 

 

 

 

 

 

 

 

 

8 Responses to How to Make a Dorset Button

  1. Wendy Norris says:

    Very easy to follow – well done.

  2. Wendy Norris says:

    PS ………. I’m left handed too.

  3. dawn says:

    for some reason I couldn’t get my head around this simple process of building a button but I can now – thank you very much for your clear instruction!

  4. Anne says:

    Thank you!
    I have been looking for an easy basic beginners tutorial, and this does the job perfectly.
    I am now going to experiment to make brooches and Christmas Tree Decorations.

  5. Kay says:

    Hi. Where can I find the instructions for making the Dorset button with the beads threaded on ? I can’t seem to “toggle” from this tutorial to the next :-\

    • Rachel Reynolds says:

      Hi Kay – I haven’t done a tutorial for the beaded on, maybe I should! All you do is thread the beads on as you make the spokes, but it can be tricky. I use beads with a hole big enough to thread onto number 10 crochet cotton (this is thinner than peele cotton) or you could make the spokes with thinner cotton. Always use an even number of beads, say four. It is very hard to explain how to hide the thread at the back, but you need to thread the back thread up through the first two beads (leave other two beads loose – they makes the first spoke) before you move on to the next spoke. That way the beads naturally form spokes around the centre of the button. Finish with a small cross stitch in the middle or fill slightly as if you are making a cross wheel. Hope that makes sense – oh the limitations of words! Would be so much easier if I could show you!!

  6. Kay Dace says:

    Hi, thanks for responding so quickly, much appreciated. I think a video showing how to do the beaded buttons would be fabulous. As you say, it is difficult to explain with words alone. But I do have a better idea of how to do this now, i.e. I didn’t realise you could change the thread to a thinner one just for the beads. Many thanks for your help. Kind regards.

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>